Page locked

This page is currently locked for editing by another user. You have to wait until this user finishes editing or the lock expires.
Currently locked by: 172.70.178.88,3.145.14.25
Lock expires at: 2025/03/15 00:56 (13 min)
This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
===== Description =====
A Wi-Fi deauthentication attack is a type of denial-of-service attack that targets communication between a user and a Wi-Fi wireless access point.

Unlike most radio jammers, deauthentication acts in a unique way. The IEEE 802.11 (Wi-Fi) protocol contains the provision for a deauthentication frame. Sending the frame from the access point to a station is called a "sanctioned technique to inform a rogue station that they have been disconnected from the network".

This attack sends disassocate packets (frames) to one or more clients which are currently associated with a particular access point.  Disassociating clients can be done for a number of reasons:

    * Recovering a hidden ESSID.  This is an ESSID which is not being broadcast.  Another term for this is "cloaked".
    * Capturing WPA/WPA2 handshakes by forcing clients to reauthenticate
    * Generate ARP requests (Windows clients sometimes flush their ARP cache when disconnected) 

An attacker can send a deauthentication frame at any time to a wireless access point, with a spoofed address for the victim. The protocol does not require any encryption for this frame, even when the session was established with Wired Equivalent Privacy (WEP) for data privacy, and the attacker only needs to know the victim's MAC address, which is available in the clear through wireless network sniffing.

=====  Usage =====

   aireplay-ng -0 1 -a 00:14:6C:7E:40:80 -c 00:0F:B5:34:30:30 ath0

Where:
  * -0 means deauthentication
  * 1 is the number of deauths to send (you can send multiple if you wish); 0 means send them continuously
  * -a 00:14:6C:7E:40:80 is the MAC address of the access point
  * -c 00:0F:B5:34:30:30 is the MAC address of the client to deauthenticate; if this is omitted then all clients are deauthenticated
  *ath0 is the interface name

===== Usage Examples =====

==== Typical Deauthentication ====
First, you determine a client which is currently connected.  You need the MAC address for the following command:

   aireplay-ng -0 1 -a 00:14:6C:7E:40:80 -c 00:0F:B5:AE:CE:9D ath0

Where:
  * -0 means deauthentication
  * 1 is the number of deauths to send (you can send multiple if you wish)
  * -a 00:14:6C:7E:40:80 is the MAC address of the access point
  * -c 000:0F:B5:AE:CE:9D is the MAC address of the client you are deauthing
  * ath0 is the interface name

Here is typical output:

   12:35:25  Waiting for beacon frame (BSSID: 00:14:6C:7E:40:80) on channel 9
   12:35:25  Sending 64 directed DeAuth. STMAC: [00:0F:B5:AE:CE:9D] [ 61|63 ACKs]

For directed deauthentications, aireplay-ng sends out a total of 128 packets for each deauth you specify.  64 packets are sent to the AP itself and 64 packets are sent to the client.

Here is what the "[ 61|63 ACKs]" means:

  * [ ACKs received from the client | ACKs received from the AP ]
  * You will notice that the number in the example above is lower then 64 which is the number of packets sent.  It is not unusual to lose a few packets.  Conversely, if the client was actively communicating at the time, the counts could be greater then 64.
  * How do you use this information?  This gives you a good indication if the client and or AP heard the packets you sent.  A zero value definitely tells the client and/or AP did not hear your packets.  Very low values likely indicate you are quite a distance and the  signal strength is poor.